The Provider ST235/85R16 Radial Trailer Tire part # TTWPRG235R16 have a 14 ply rating. In regards to mounting, most local auto repair shops should be able to assist. Please note, balancing is not required for trailer tires. We do offer this tire pre-mounted as well, the Provider ST235/85R16 Radial Trailer Tire w/ 16" White Spoke Wheel part # TTWA16RGWSHD. view full answer...
I wouldn't describe the release cable of the BAK Revolver X2 part # BAK39329 as flimsy. It's actually a rubber coated steel cable that we've not had any reported issues of breaking. If it were to break this is covered by a 3 year warranty though so BAK or us would take care of it. There isn't a replacement part for it since it's not a commonly damaged item. view full answer...
The Cam Tightening Tool # PW204 is designed to fit the cams on Pewag and Glacier brand heavy truck tire chains. The tool is made from bent bar stock. I went to our warehouse and measured it for you. The cam tool has a cross section of 1/4-inch x 7/8-inch.
We do not sell the Quick Grip brand so I checked the specs for a number of their tire chains that use cams, but the cam's dimensions are not provided. view full answer...
Yes, the Du-Ha Truck Storage Box part # DU10037 will carry two rifles as well as your jack and other tools in the bins that are on either side of the gun rack like in the picture I attached. view full answer...
The Buffalo Tools electric car jack # BTEJ212 is rated for 2,000 pounds. Since it is only lifting part of the vehicle and not the whole weight of the vehicle it can be used to change a tire on your 2014 Honda Odyssey.
Once you have the vehicle up high enough it should then be let down on jack stands such as # PTW41021 since jacks are not meant to hold the weight by themselves. view full answer...
I spoke with my contact at Performance Tool and she informed me that the Performance Tool Wheel Step, part # PT68ZR, has a weight limit of 300 lbs. view full answer...
Trailer wheels are usually rated for much higher PSI than the tire or valve stem used, so they are not typically listed. So long as the valve stem and tire are rated for 100 psi, there should be no issue using these wheels.
The wheel your referencing the Aluminum HWT Series S5 Trailer Wheel # AM22658HWTB is a 16"x 6.5" aluminum wheel, with a 6 on 5-1/2 bolt pattern and has a 3,580 lbs load rating.
If you need 8 lug wheels the Aluminum HWT Series S5 Trailer Wheel # AM22659HWT is an 8... view full answer...
A trailer axle is the most important factor in determining the trailer capacity but there can be other factors such as the suspension components, wheels and tires, and even the trailer frame itself. You would probably need to beef up the frame if you are adding a second axle or axle-less suspension system or replacing the axle with an axle-less system such as # ASR5200S01. And you would also need wheels and tires to match the higher capacity.
You would need to use hub # 8-213-5UC1-EZ with... view full answer...
I cannot confirm a fit of the Replacement Lock Cylinder for BOLT Toolbox Latch - Codes to Ford Side-Cut Key # BL7025636 for your spare tire cover in the bumper of your 2016 Ford F-150. I can say that it is an excellent question and would take out the issues with other locks and the lost key issue since it codes to your ignition key. This cylinder fits standard 3/4 inch hole of toolboxes.
This product does require the Retaining Nut for BOLT Tool Box Latch Lock Cylinder # BL4306752. view full answer...
I went to our warehouse so I could measure the housing of the Tru-Flate Top Off Mini Tire Inflator # 16-230. The housing of this unit measures 4-3/4 x 3-3/4 x 2-1/4-inches. The length of the inflation hose is 4-inches and the length of the 12VDC power cord that plugs into your accessory outlet is 9-feet.
This unit can deliver a maximum psi air pressure of 45-psi. Time required to completely fill a standard tire is approximately 10 minutes.
For only a bit more we offer the 100-psi-capable... view full answer...
All of our 8 inch wheels have a 2.5 inch pilot hole diameter. To determine if they will work on your hubs, you will want to measure the base of the hub bore with a precise measuring tool such as a dial caliper. If the base of the hub bore has an outer diameter that is slightly less than 2.5 inches, then the Kenda Tire and Wheel Combo, # AM30120, will fit. If the outer diameter is exactly 2.5 inches or more, then this wheel will not fit. view full answer...
Yes, the Viair TLC BOOST Air Compressor item # VA37WR can be permanently mounted to your vehicle. The hardware necessary to install the compressor is included. It does work with all kinds of valve stems.
This 1.5 gallon air tank fills from empty to 120 psi in under 90 seconds. The inflation attachment has a built in pressure gauge so you can easily see how full you are airing up your bike tires. view full answer...
We have the FloTool RhinoRamps part # FT11912MI which are rated for 16,000 lbs. It provides a lift of up to 6-1/2 inches and works on up to 10 inch wide tires. view full answer...
Since you have a service body truck, I recommend the Viair TLC BOOST XL Heavy-Duty Air Compressor item # VA97WR. You're going to want the tank and the larger compressor. This heavy duty compressor charges the 2 gallon tank to 150 psi in just 2-1/2 minutes. This gives it the ability to inflate tires up to 33".
This compressor can be hard mounted to your F-350 with included mounting kit and wired directly to your battery. This kit also includes a 30' hose, a blow gun, and a inflation tool... view full answer...
Trailer spindle and bearing tolerances are pretty tight, usually down to a thousandth of an inch. Use of emery cloth on a spindle to remove scoring damage might remove enough material to affect the fit of the replacement bearing. You can be off the original dimension by perhaps 1/1000th of an inch but not much more than that.
If you have a precision caliper that can read to 1/1000th of an inch you can check that repaired spindle's diameter where the bearings ride (and use another undamaged... view full answer...
You will first need to determine what the towing capacity is for your 2014 Subaru Outback and then determine how much your trailer will weigh when it is loaded at its max. I attached and FAQ article on determining tongue weight that should be very helpful.
If you determine that your trailer weighs less than the max capacities listed for your vehicle then you would have no problem using your vehicle to tow your trailer.
You will also want to make sure that your trailer is being towed as... view full answer...
If your 2014 Ram 3500 has a factory rail kit, then measure the front puck to the back edge of your bed. It will provide you the approximate distance from B&W Companion 5th wheel hitch # BWRVK3600 to the bed front edge to determine the width of a tool box you can add.
If you don't have a factory rail kit, measure from the centerline of the rear axle (easiest to stand by the rear tire) move forward 1-9/16 inch and then begin measurement to the back edge of the truck bed cab. Then subtract... view full answer...
For your 2017 Ram 2500 Tradesman, the best option for air bags is going to be the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item # AL88289. These Air Lift springs have a 5,000 lbs load leveling capacity. The included jounce bumpers will offer even more support when your air bags are running at a lower PSI.
I have added an installation video below.
For an onboard air compressor with gauges you will want to use the Air Command II Xtreme Duty Compressor... view full answer...
To add a set of heavy duty air bags to your 2024 Ford F-250, I recommend the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs item # F95FV. These air bags have a 7,500 lbs capacity that will level out the rear end of your F-250 when you are towing your 5th wheel trailer. This kit includes custom fit brackets that are compatible with all 5th wheel hitches and install in pre-existing holes.
I have linked an installation video below so you can see how to get these air bags installed.... view full answer...
Go To Results